Battery Motor
QMotion battery automated shades are powered by an internal pack of standard D-cell or AA batteries depending upon shade size. The estimated average battery life is two years, dramatically reducing maintenance cost and adding convenience. (Shade size, usage and installation environment determine actual battery life.)
Available in Gen3 and ZigBee HA 1.2 |
QIS Motor
Qadvanced Intelligent System (QIS) Hardwired Roller Shades use standard off-the-shelf Cat5e or Cat6 cable for both power and communications. The QIS motor also comes with the option to control the shades wirelessly using ZigBee H.A. 1.2 technology. NOTE: Do NOT use Power over Ethernet (PoE) or any Ethernet wiring or powering scheme. This will damage the shade motors and void the warranty.
Available in RS485 and ZigBee HA 1.2 |
Low Voltage Motor
The Low Voltage shades use 22AWG/24V connector wires from the shade controller (MCA). Power supply and distribution box options are available. The Low Voltage system is great for standalone applications where there is limited potential interference from other electronic devices for remote control.
Available in Gen3 |
|
|
Power Springs
|
Torsion Spring
|
|
• Control QMotion shades with iOS and Android mobile devices
• Virtual Shade: Drag your finger to place the shade to the desired positions. • “Plug and Play” - Easy Set-up. • Channel System to name, take and set reference photo to group shades and create “scenes”. • Step by Step setup for learning, setting lower limit, and deleting shades • TCP/IP to 433Mhz bridge. • Set up once and settings sync to other smartphones and tablets on the network . |
|
• Controls Qadvanced with ZigBee HA1.2 roller and honeycomb shades.
• Supports up to 32 devices per Qube, or 95 devices maximum per ZigBee HA1.2 network if using Range Extenders. Devices are defined as Qadvanced shades and QdR remotes. • Qube without Range Extender supports any combination of 32 shades and remotes. • Qube with Range Extender - a Range Extender takes up one of the 32 positions; 2 range extenders = 2 positions. • Qube must be plugged into a local WiFi router for programming, using the QMotion app with the Qube, and controlling the shades. • Once programmed on the Qube coordinator with your smart device and our app, shades can be controlled with your smart device on any WiFi network through the cloud. Now you can control your shades from almost anywhere! |
|
|
|
• Used to create a ZigBee mesh network as the extender is paired into the system.
• Works with roller shades powered by QMotion ZigBee technology. • Use as many as required in an installation (refer to limits when used with Qube). • Please note - the original Range Extender may be used in a stand-alone installation, the RZ2 only works as an extender. |
|
|
|
• DC output: 24 Volt, 7.5 Amps
• AC input: 100-240 Volts ~ 2.5 Amps • Wall Mounted Switches receive power through Power Over Cable (POC) • RJ-45 Ports for Motorized Shades and and switches - Quantity 8 • Communication Ports (RJ-45) - Quantity 2 |
|
QMotion’s Wiring Adapter allows for pre-wired cabling to easily connect to QIS shades, resulting in simple and convenient access to roller shades powered by QIS motors without rewiring your entire system. This 6 inch adapter allows for the translation of communication and power without the added expense of proprietary cabling.
|
|
|
|
Including fashionable, color-coordinated fascias will enhance both the form and function of your QMotion shades. Easily mounted either inside or outside the window width, fascias attractively conceal the shade system while adding to the light protection your shades were designed to provide. So they’re pretty and practical, all in one.
|
